First, test your pool water’s pH and alkalinity levels and adjust the levels according to manufacturer’s instructions. To properly clean a Purechlor salt cell, it is important to balance pH levels and sanitize the cell using an appropriate sanitizer. Once the cell is clean, it can be reconnected and the green light should stop blinking. To do this, you should disconnect the cell from your chlorine generator, remove any build-up, and thoroughly rinse off any debris and dirt. The green blinking light indicates that it is time to clean the cell and restore its functionality. This build-up reduces the efficiency of the current, resulting in a decrease in chlorine production. Salt cells are used in chlorine generators to keep a pool’s chlorine level consistent, and over time, calcium and other minerals can build up and require regular cleaning. Your salt cell is most likely blinking green to indicate that it needs to be serviced. Therefore, when it says check salt cell, it means to check the salt levels in the pool water and make sure they are within the proper range. In addition to monitoring the salt cell’s performance, checking the salt levels of your pool water is important in order to make sure there are not too much salt in your pool, as high levels of salt can cause corrosion of metal objects in the pool, such as ladders and pipes, as well as damage to the pool liner and pool chemicals.Ĭhecking the salt cell involves testing the salt levels in a pool and ensuring the levels are between 3000-3500 ppm (parts per million). Over time, these electrodes need to be monitored and tested to make sure they are in good condition and able to properly generate chlorine and run efficiently. Salt cells, also known as chlorinators, are an integral part of pool maintenance that generate chlorine in the pool to help control bacteria and algae growth.Ī salt cell consists of two electrodes that when submerged in the pool water, react with the salt in the water to produce chlorine. What does it mean when it says check salt cell?Ĭhecking a salt cell is a process used to test the levels of salt in your pool water. The check cell light should have reset itself, but if it doesn’t, you will need to replace the chlorine cell. If all the wires and connections appear to be secure, wait for 30 minutes before reconnecting the power to the system and turning the switch back on. Once the pump is off, disconnect the power supply to the Purechlor unit.Īfter the power has been disconnected, check the wiring and connections for breaks or loose connections. To reset the check cell light, you will first need to turn off your pool pump. The check cell light indicates that there is a malfunction in the chlorine cell of your Purechlor salt chlorinator. How do I reset check cell light on Purechlor? Finally, once you’ve reset the system and reprogrammed it if necessary, it should be ready to use. Refer to your instruction manual for specific instructions.ĥ. After the system is reset, you may need to reprogram it, depending on the model of system you’re using. Once reconnected, turn on the power switch, and press the reset button that’s located inside the system. After you understand the procedure, disconnect the power from the Hayward Check System and wait for at least 10 minutes before reconnecting it.ģ. It should tell you the exact procedure for resetting the device.Ģ. First, take a few minutes to read through the instruction manual that came with your system. If you need to reset your Hayward Check System, the process is quite simple:ġ. Your AquaRite panel should now be reset and ready to be used in your pool environment. Make sure to note down the current settings before you reset them. After plugging the panel back in, reset all your settings via the menus on the panel’s display. If you aren’t sure which one it is, you may need to consult your manual for help.ĥ. Find the electrical conduit or power source to the panel, and unplug it from the power source. It’s typically near your pool’s pump and filter configuration, but the exact placement will depend on the make and model of your system.Ģ. To reset the AquaRite panel, follow these steps:ġ. Therefore, it’s important to note these items down so they can be reset afterward. Resetting your panel will clear certain settings and defaults, such as the current water temperature, total hours of operation, and, in some cases, the salt level. Resetting your AquaRite panel is a pretty simple process, but it’s important to understand what it will do before you take action.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |